PART IFishing Vessels Exceeding 15 Tons, Gross Tonnage (continued)
Construction of Hulls (continued)
(2) Where a fishing vessel proceeds more than 20 nautical miles from land and there is no method of preventing water from entering the main hull through a broken window or port light, storm shutters and deadlights respectively shall be fitted to those openings.
(3) Plate glass having a minimum thickness of 6 mm shall be fitted in the wheelhouse windows of
(4) All doors giving access to the main hull of a fishing vessel shall be strongly constructed and hung on substantial hinges and locking arrangements shall be such that a door can be opened from either side.
(4.1) Subject to subsection (4.3), a fishing vessel shall have at least two means of escape, including the main entrance, in each crew space and area in which the crew may be normally employed.
(4.2) For the purposes of subsection (4.1), one of the means of escape shall be located as far as possible from the main entrance and may be a window or a scuttle that is of sufficient proportions to provide for easy exit by the crew members and that is capable of being retained in an open position while being used as an escape route.
(4.3) The requirements of subsections (4.1) and (4.2) do not apply
(5) Where entrance to the crew space on a fishing vessel is by way of the engine room, an escape hatch shall be fitted from the crew space to the open deck.
(6) Where exit from the crew space of a fishing vessel to the open deck is provided by one means only, it shall be of sufficient proportions to provide for easy exit for the number of men berthed and shall be as near the centre line of the ship as is practicable.
(7) Two engine room entrances providing easy access, each measuring at least 560 mm by 560 mm, shall be fitted on a fishing vessel unless this is not practicable, in which case one engine room entrance shall be fitted that is placed as near the centre line of the vessel as is practicable and that measures
- SOR/89-96, s. 3
- SOR/95-372, s. 7
- SOR/2016-163, ss. 14, 35(F)
28 (1) Subject to subsections (2) and (3), bulwark, rails, chains, wire rope or any combination of these shall be fitted around the weather deck of a fishing vessel at least 760 mm in height above the weatherdeck.
(2) The bulwarks, rails, chains and wire rope referred to in subsection (1) may be portable or be dispensed with in places where they would interfere with the fishing operations of the vessel.
(3) The bulwarks, rails, chains or wire rope referred to in subsection (1) may be less than 760 mm in height in way of deckhouses if suitable handrails are fitted on the sides of such deckhouses.
- SOR/2016-163, ss. 15, 35(F)
29 [Repealed, SOR/2016-163, s. 16]
29.1 (1) Subject to subsections (2) to (4), where bulwarks on weather parts of the working deck of a fishing vessel form wells, the minimum freeing port area, expressed in square metres, in respect of each such bulwark shall be not less than
where l, expressed in metres, is the lesser of the length of bulwark in the well and 70 per cent of the length of the vessel.
(2) Where the height of the bulwark in a well on the working deck is more than 1,200 mm, the minimum freeing port area shall be increased, for each 100 mm in excess of 1,200 mm, by 0.004 m2 per metre of length of well.
(3) Where the height of the bulwark in a well on the working deck is less than 900 mm, the minimum freeing port area may be decreased, for each 100 mm less than 900 mm, by 0.004 m2 per metre of length of well.
(4) Where the vessel’s sheer is such that the minimum freeing port areas, calculated in accordance with subsections (1) to (3), do not provide rapid and effective freeing of water from the deck, those areas shall be increased by such amount as will provide rapid and effective freeing of water from the deck.
(5) The freeing ports of every fishing vessel shall be arranged along the length of bulwarks so as to provide rapid and effective freeing of water from the deck of the vessel, and the lower edges of the freeing ports shall be as close to the deck as possible.
(6) On every fishing vessel, poundboards shall be stowed, and means of stowage of fishing gear shall be arranged, in such a manner that the effectiveness of the freeing ports of the vessel is not impaired.
(7) Every poundboard on a fishing vessel shall be so constructed that it can be secured in position when in use and will not hamper the rapid and effective freeing of water from the deck of the vessel.
(8) Every freeing port over 300 mm in depth of a fishing vessel, shall be fitted with bars spaced not more than 230 mm apart, or with other suitable protective devices.
(9) Where the protective devices fitted in accordance with subsection (8) are covers, they shall be of a construction approved by the Minister.
(10) In a fishing vessel intended to operate in areas subject to icing, protective devices fitted in accordance with subsection (8) shall be capable of being easily removed to restrict or reduce ice accretion.
- SOR/79-93, s. 2
- SOR/79-905, s. 4
30 [Repealed, SOR/2016-163, s. 17]
31 [Repealed, SOR/2016-163, s. 17]
32 [Repealed, SOR/2016-163, s. 17]
33 [Repealed, SOR/2016-163, s. 17]
34 [Repealed, SOR/2016-163, s. 17]
34.1 [Repealed, SOR/2016-163, s. 17]
Fire Extinguishing Equipment
35 [Repealed, SOR/2016-163, s. 18]
36 [Repealed, SOR/2016-163, s. 18]
37 [Repealed, SOR/2016-163, s. 18]
38 (1) Every fishing vessel exceeding 12.2 m in length shall be equipped with at least one hand or engine driven pump and apparatus whereby a suitable jet of water can be directed into any part of the ship.
(2) The internal diameter of the pipes for the pump mentioned in subsection (1) shall be not less than 19 mm.
(3) Subject to subsection (4), bilge pumps on a fishing vessel may be used as fire pumps by using them to pump sea water on deck.
(4) Where two bilge pumps are required on a fishing vessel, neither pump shall be used to pump sea water on deck unless it is possible for one bilge pump to pump bilge water overboard while the other pumps sea water on deck.
(5) Subject to subsection (6), the piping for a fire pump on a fishing vessel shall be of steel, bronze or other material that is suitable for the purpose, and the joints for such piping shall be flanged or screwed.
(6) Where it is necessary to reduce the effect of vibration, short lengths of rubber or plastic hose may be installed and shall
- SOR/95-372, s. 7(E)
- SOR/2016-163, ss. 19, 35(F)
(2) Wooden bulkheads behind cooking or heating appliances on a fishing vessel shall be insulated if space constraints do not allow the free circulation of air all around and below the appliance.
(3) Every fishing vessel of not more than 24.4 m in length that is provided with a liquefied petroleum gas installation shall comply with the requirements of the Marine Machinery Regulations for such vessels.
- SOR/83-272, s. 1
- SOR/95-372, s. 7
- SOR/2016-163, ss. 20, 35(F)
- Date modified: